VLAN Pruning یا پاکسازی VLAN در شبکه سیسکو یک فرایند است که برای بهینهسازی ترافیک شبکه و کاهش بار و پهنای باند لازم برای انتقال دادهها استفاده میشود. VLAN Pruning به شما امکان میدهد تا ترافیک بین VLAN هایی که نیاز به ارتباط با یکدیگر ندارند را حذف کنید و از منابع شبکه صرفهجویی کنید.
در شبکههای سیسکو، هر VLAN در یک سوئیچ به عنوان یک بستر منطقی برای ترافیک اختصاص داده میشود. وقتی یک بستر فیزیکی (مانند یک لینک اترنت) بین دو سوئیچ وجود دارد، تمام ترافیک VLAN ها به طور پیش فرض از طریق آن لینک ارسال میشود. این ممکن است به معنای هدررفت پهنای باند باشد، زیرا تمام ترافیک VLAN ها به هر VLAN میرود، حتی اگر نیاز به ارسال به آن VLAN نباشد.
با استفاده از VLAN Pruning در شبکه سیسکو، میتوانید این مشکل را برطرف کنید. VLAN Pruning بر اساس پروتکل VTP (VLAN Trunking Protocol) اجرا میشود و به صورت خودکار ترافیک بین سوئیچها را محدود میکند. هنگامی که VLAN Pruning فعال شود، سوئیچها در هر لینک فقط ترافیک VLAN هایی را ارسال میکنند که در آن لینک لازم است.
برای فعال کردن VLAN Pruning در شبکه سیسکو، شما باید از دستور زیر در وضعیت پیکربندی سوئیچ استفاده کنید:
``` Switch(config)# vlan pruning ```
بعد از فعال شدن VLAN Pruning، سوئیچها به صورت خودکار VLAN هایی که در لینک مورد نظر لازم نیستند را از ترافیک حذف میکنند. این عمل به صورت دینامیک انجام میشود و هرگاه ترافیک VLAN مورد نظر برای ارسال به یک سوئیچ دیگر وجود داشته باشد، VLAN Pruning آن را بازگردانده و ترافیک را ارسال میکند.
استفاده از VLAN Pruning در شبکه سیسکو میتواند منجر به بهبود عملکرد شبکه، کاهش ترافیک غیرضروری و صرفهجویی در پهنای باند شود.
VLAN pruning in Cisco networks is a process used to optimize network traffic and reduce the burden and bandwidth required for data transmission. VLAN pruning allows you to eliminate traffic between VLANs that do not need to communicate with each other, thus conserving network resources.
In Cisco networks, each VLAN is assigned as a logical segment for traffic. When there is a physical link (such as an Ethernet link) between two switches, by default, all VLAN traffic is sent over that link. This can result in bandwidth wastage because all VLAN traffic goes to every VLAN, even if it does not need to be sent to that VLAN.
By utilizing VLAN pruning in Cisco networks, you can address this issue. VLAN pruning is executed based on the VLAN Trunking Protocol (VTP) and automatically limits traffic between switches. When VLAN pruning is enabled, switches only send the VLAN traffic that is necessary for each specific link.
To enable VLAN pruning in Cisco networks, you need to use the following command in switch configuration mode:
``` Switch(config)# vlan pruning ```
Once VLAN pruning is activated, switches automatically remove VLANs that are not needed for a specific link from the traffic. This action is performed dynamically, and whenever there is VLAN traffic intended for another switch, VLAN pruning restores it and forwards the traffic.
Using VLAN pruning in Cisco networks can lead to improved network performance, reduced unnecessary traffic, and bandwidth savings.